|
|
|
|
Section 1: Identification of the Substance or Mixture and of the Supplier
- GHS product identifier
- Other means of identification
- Recommended use of the chemical and restrictions on use
- Supplier’s details (including name, address, phone number etc.)
- Emergency phone number
|
Section 1: Identification of the substance/mixture and of the company
1.1 – Product identifier REACH registration number for the substance where available. For mixtures, registration numbers should be put in section 3 for each hazardous substance inside the mixture. If a Unique Formula Identifier (UFI) needs to be indicated in the SDS. This is to be listed in the subsection “Other means of identification”
1.2 – Relevant uses and uses advised against 1.3 – Details of the supplier of the Safety Data Sheet
An e-mail address for a competent person responsible for the safety data sheet should be given in addition to the full address and telephone number of the supplier. 1.4 – Emergency contact information Any limitations on the emergency number's use such as types of information and hours of service should be noted. The EU Member State may have designated an authority's emergency number which is required to be used. Please refer to the country specific information. Some countries' requirements are listed as part of the list of National Helpdesks but this may be incomplete: National Helpdesks List Where no authority is specified by the country, the number does not have to be in-country, but it must provide the language of the member state where the product is placed on the market.
|
|
Section 2: Hazards Identification
- GHS classification of the substance/mixture and any national or regional information
- GHS label elements including precautionary statements. (Hazard symbols may be provided as a graphical reproduction of the symbols in black and white or the name of the symbol e.g. "flame")
- Other hazards which do not result in classification (e.g. "dust explosion hazard") or are not covered by the GHS
|
Section 2: Hazards Identification
2.1 – Classification of the substance or mixture Based on the CLP regulation 2.2 – Label elements Based on the CLP regulation 2.3 – Other hazards
|
|
Section 3: Composition/Information on Ingredients
Substance
- Chemical identity
- Common name, synonyms, etc.
- CAS number and other unique identifiers
- Impurities and stabilizing additives which are themselves classified and which contribute to the classification of the substance
Mixture
- Chemical identity
- Concentration or concentration ranges of all ingredients which are hazardous within the meaning of the GHS and are present above their cut-off levels
NOTE: For information on ingredients, the competent authority rules for CBI take priority over the rules for product identification.
|
Section 3: Composition/information on ingredients
The identifier, concentration or concentration ranges and the CLP classification of the substance or the substances in the mixture that are required to be listed. For substances in a mixture that are required to be disclosed, the registration number, EC number, CAS number and IUPAC number should all be given where available. See EU Regulation (EC) 1907/2006 (REACH) as amended, Annex II, Part A, section 3 for full details of rules for disclosure. Only 3.1 or 3.2 should be applied. For a substance in a mixture that is required to be listed by the regulation, the only way to protect this information for trade secrecy is to apply for an alternative chemical name (See Alternative chemical name section)
|
|
Section 4: First-Aid Measures
- Description of necessary measures subdivided according to the different routes of exposure, i.e. inhalation, skin and eye contact and ingestion
- Most important symptoms/effects, acute and delayed
- Indication of immediate medical attention and special treatment needed if necessary
|
Section 4: First aid measures
4.1 – Description of first aid measures 4.2 – Most important symptoms and effects, both acute and delayed 4.3 – Indication of any immediate medical attention and special treatment needed
|
|
Section 5: Fire-Fighting Measures
- Suitable and unsuitable extinguishing media
- Specific hazards arising from the chemical (e.g. nature of any hazardous combustion products)
- Special protective equipment and precautions for fire fighters
|
Section 5: Firefighting measures
5.1 – Extinguishing media 5.2 – Special hazards arising from the substance or mixture 5.3 – Advice for firefighters
|
|
Section 6: Accidental Release Measures
- Personal precautions, protective equipment and emergency procedures
- Environmental precautions
- Methods and materials for containment and cleaning up
|
Section 6: Accidental release measures
6.1 – Personal precautions, protective equipment and emergency procedures 6.2 – Environmental precautions 6.3 – Methods and material for containment and cleaning up 6.4 – Reference to other sections
|
|
Section 7: Handling and Storage
- Precautions for safe handling
- Conditions for safe storage including any incompatibilities
|
Section 7: Handling and storage
7.1 – Precautions for safe handling 7.2 – Conditions for safe storage, including anything that is incompatible 7.3 – Specific end use(s)
|
|
Section 8: Exposure Controls/Personal Protection
- Control parameters e.g. occupational exposure limits or biological limit values
- Appropriate engineering controls
- Individual protection measures, such as personal protective equipment
|
Section 8: Exposure controls/personal protection
8.1 – Control parameters
Union values and national values for the country where SDS is being provided, regardless of their concentration, see REACH Annex II, Part A, section 8 for full details.
If the SDS contains Exposure Scenarios, the applicable DNELs and PNECs for the substance should be listed.
8.2 – Exposure controls
8.2.1 Appropriate engineering controls 8.2.2 Personal protection equipment Taking into account Council Directive 89/686/EEC (91) and referring to the appropriate CEN standards, detailed specifications shall be given on which equipment will provide adequate and suitable protection 8.2.2.1 Eye and face protection 8.2.2.2 Skin protection Hand protection Other skin protection 8.2.2.3 Respiratory protection 8.2.2.4 Thermal hazards 8.2.3 Environmental exposure controls
|
|
Section 9: Physical and Chemical Properties
- Physical state
- Colour
- Odour
- Melting point/freezing point
- Boiling point or Initial boiling point and boiling range
- Flammability
- Lower and upper explosion limits/flammability limit
- Flash point
- Auto-ignition temperature
- Decomposition temperature
- pH
- Kinematic viscosity
- Solubility(ies)
- Partition coefficient: n-Octanol/Water
- Vapour pressure
- Density and/or relative density
- Relative vapour density
- Particle characteristics
|
Section 9: Physical and chemical properties
9.1 – Information on basic physical and chemical properties Identify the following properties:
- Physical state
- Colour
- Odour;
- Melting point / freezing point
- Boiling point or initial boiling point and boiling range
- Flammability
- Lower and upper explosion limit
- Flash point
- Auto-ignition temperature
- Decomposition temperature
- pH
- Kinematic viscosity
- Solubility
- Partition coefficient n-octanol/water (log value)
- Vapour pressure
- Density and/or relative density
- Relative vapour density
- Particle characteristics
9.2 – Other information
|
|
Section 10: Stability and Reactivity
- Reactivity
- Chemical stability
- Possibility of hazardous reactions
- Conditions to avoid
- Incompatible materials
- Hazardous decomposition products
|
Section 10: Stability and reactivity
10.1 – Reactivity 10.2 – Chemical stability 10.3 – Possibility of hazardous reactions 10.4 – Conditions to avoid 10.5 – Incompatible materials 10.6 – Hazardous decomposition products
|
|
Section 11: Toxicological Information
Concise but complete and comprehensible description of the various toxicological effects and available data used to identify those effects including:
- Information on the likely routes of exposure (inhalations, ingestion, skin and eye contact)
- Symptoms related to the physical, chemical and toxicological characteristics
- Delayed and immediate effects and also Chronic effects from short and long-term exposure
- Numerical measures of toxicity (such as acute toxicity estimates)
|
Section 11: Toxicological information
11.1 – Information on hazard classes as defined in Regulation (EC) No 1272/2008 The relevant hazard classes, for which information shall be provided, are
- Acute toxicity
- Skin corrosion/irritation
- Serious eye damage/irritation
- Respiratory or skin sensitization
- Germ cell mutagenicity
- Carcinogenicity
- Reproductive toxicity
- STOT-single exposure
- STOT-repeated exposure
- Aspiration hazard.
11.2 – Information on other hazards
|
|
Section 12: Ecological Information
- Ecotoxicity (aquatic and terrestrial, where available)
- Persistence and degradability
- Bioaccumulative potential
- Mobility in soil
- Other adverse effects
|
Section 12: Ecological information
12.1 – Toxicity 12.2 – Persistence and degradability 12.3 – Bioaccumulative potential 12.4 – Mobility in soil 12.5 – Results of PBT and vPvB assessment 12.6 - Endocrine disrupting properties 12.7 – Other adverse effects
|
|
Section 13: Disposal Considerations
Description of waste residues and information on their safe handling and methods of disposal, including the disposal of any contaminated packaging
|
Section 13: Disposal considerations
13.1 – Waste treatment methods (format not mandatory)
13.1.1 Product / Packaging disposal: Waste codes / waste designations according to List of Waste (LoW): 13.1.2 Waste treatment-relevant information 13.1.3 Sewage disposal-relevant information 13.1.4 Other disposal recommendations
|
|
Section 14: Transport Information
- UN number
- UN proper shipping name
- Transport hazard class(es)
- Packing group if applicable
- Environmental hazards (e.g. marine pollutant (Yes/No))
- Transport in bulk
- Special precautions which a user needs to be aware of, or needs to comply with, in connection with transport or conveyance either within or outside their premises
|
Section 14: Transport information
14.1 – UN Number 14.2 – Proper shipping name 14.3 – Hazard class 14.4 – Packing group 14.5 – Environmental hazards 14.6 – Special precautions for the user 14.7 – Maritime transport in bulk according to IMO instruments
|
|
Section 15: Regulatory Information
Safety, health and environmental regulations specific for the product in question
|
Section 15: Regulatory information
15.1 – Safety, health and environmental regulations/legislation specific for the substance or mixture 15.2 – Chemicals safety assessment
|
|
Section 16: Other Information
Other information including information on preparation and revision of SDS
|
Section 16: Other information
See Annex II, Part A, section 16 for details.
|
| |
ANNEX: Exposure scenarios
The format of the Exposure Scenario (ES) consists of 4 sections:
- Title section
- Conditions of use affecting exposure
- Exposure estimation and reference to its source
- Guidance to Downstream User (DU) to evaluate whether he works inside the boundaries set by the ES
|